Mandalorian Super Commando Grunt Diagonal and Vertical Hand print

[DTCorvus]

So for about a week now I have been working on the CRL’s for the Mandalorian Super Commando Grunts, both the Vertical and Diagonal hand print versions. Now my personal belief is that the the Deathwatch Mandalorians have been misplaced in the Detachment they are currently assigned. Only Jango and Boba are bounty hunters  and them being in BHG is appropriate. Yet the Clone Wars Mandalorians were grouped into BHG as well even though it was never stated that they were bounty hunters or not. Now since these characters are featured in the Clone Wars animated show they could be grouped into Flagship Eclipse because they are a canon character from an “Expanded Universe” source. Now I’m not saying that the character who are already assigned to BHG are to be moved but going forward the newly approved Mandalorians whether it be the Deathwatch Super Commandos or the imperial super commandos be placed in Flagship Eclipse. Since the characters I have been working on the CRL’s for have no posted CRL it could be easily done.
Now just in case this doesn’t go further in the Detachment switch I am posting these CRL’s to both the Bounty Hunters Guild and Flagship Eclipse Detachment forums. I am working on one of the costumes of the characters I have written the CRL (Diagonal hand print). Of course these will not be set in stone at first and will be up for review and revisions. Also who knows if there are any more people who have this costume so that there will be a visual reference or will the CRL list be a yellow tag with just the text waiting for a visual reference. I hope these will pass the muster for 501st standards.

 

Mandalorian Super Commando Grunt Diagonal Handprint 
•    Helmet
    ◦    An animated Deathwatch style helmet must be used.
    ◦    The dome, face, and back is painted metallic grey, light grey or silver. The mandibles, key slot indentation, and band are painted red. The upper cheeks are painted a dark grey and the lower cheeks are painted metallic grey, light gray or silver.
       ◦    A stylized hand print is placed on the face of the helmet diagonally with the fingertips pointing up to the left. The handprint is painted black with drip marks running down from it.  
    ◦    The helmet should have the narrower design with the longer face and the T should come to points at the ends.
      ◦    The visor should be dark in color to obscure the wearers face.
    ◦    There are no diamonds on the forehead of the helmet.
    ◦    The right earcap must match the left.
    ◦    As with the Clone Wars season 2 Death Watch grunt there is no RF for the Season 4 Death Watch Grunts.
•    Shoulder Plates
       ◦    Must be Animated Death Watch style armor.
       ◦    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
       ◦    Must have 4 points with an inward curve connecting the top and bottom point on each outside edge.
    ◦    They are painted red in color and are weathered through.
       ◦    Armor is connected securely to Flak Vest shoulder tabs.
       ◦    Shoulder armor flares out off the shoulders to present a wider than normal silhouette. 
•    Chest Armor
    ◦    Chest armor must be the animated Deathwatch style and consist of two chest plates, ab plate, diamond, and collar plate.
    ◦    Upper chest plates are hastily painted red in color, showing brush strokes and weathered throughout.
      ◦    The chest diamond is painted red in the same fashion as the upper chest armor. The diamond also has a raised thin rectangular piece in its center.
      ◦    The collar plate is painted red in color in the same fashion as the upper chest plates and weathered throughout
      ◦    The abdominal plate is a dark charcoal grey in color with slight red over spray from upper chest and weathered throughout
    ◦    The chest slots are cut out. The slots should be painted with red paint.
•    Back Plate
    •    Must be Animated Death Watch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must have curved cutout at the bottom.
    •    Interior curved area should match black on armor.
    •    Should curve in towards wearer on all edges to give appearance of thickness, and sit flush against wearers back.
    •    NOTE: Collar and backplate DO NOT overlap.
    ◦    It is ultra flat black in color.
•    Cod Armor
        •    Must be Animated Deathwatch style armor.
    •    Triangular cod piece which must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    ◦    Bottom must curve inward toward the inseam of the wearer.
    •    Must be tucked under the girth belt.
    ◦    It is dark charcoal grey in color and weathered through slightly.
•    Thigh Armor
    ◦    Must be the animated Deathwatch style armor.
      Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    ◦    The plate rides on the outside of the thigh rather than on the front of the thigh.
    ◦    The holsters are built into the thigh plate and appear as part of the armor.
          •    Armor wraps around the outer thigh with no visible straps/attachment.
    •    Must feature a solid box holster on each leg.
    ◦    Rear upper section of holster box is shorter than front to accommodate Westar pistols
    ◦    They are ultra flat black in color.
•    Knee Plate
          •    Must be Animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be painted black and weathered to match references.
    •    Armor attaches to the front of the knees, directly to flight suit with no straps or visible means of attachment
    ◦    The base color is flat silver/light grey. This base color is shown through the weathering.
•    Shin Armor
        •    Must be Animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be painted metallic grey, light gray or silver and weathered to match references.
    •    Must fit closely around the shin.
    •    Must be made of three angled sections: flat front and angled flat sides that curve at back slightly to fit wearers leg. The tops of the side segments must be angled downwards.
    •    Armor attaches directly to flight suit with no straps or visible means of attachment. 
•    Boot Armor
    ◦    Must be animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Armor consists of Top of the foot cover, Toe Cap and Heel Cover with rectangular raised detail that wraps around back of heel.
    •    Must be painted charcoal grey/black and weathered to match references.
    •    Boot armor connects with no visible means of attachment
    ◦    Near the ankle, the armor should be ultra flat black in color.
•    Spat
    ◦    No spats should be used for the TCW Deathwatch builds.
    ◦    Although due to CGI cheat in the show portrays some movement that could be considered less than hard armor, it has been decided it’s due to animation not actual portrayal.
•    Hand Plates
    ◦    The hand plates are a completely custom design in a ‘tombstone’ shape.
    ◦    They are ultra flat black in color and weathered slightly through.
•    Gauntlets
    ◦    The gauntlets are a completely custom design and do not match the season 2 Death Watch gauntlets.
    ◦    They are a set of clamshell cylinder gauntlets.
    •    Must be Animated Deathwatch style armor.
    •    May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be worn with indented "closure" on the inside of the arm.
    •    Must have two raised platforms on the top of the gauntlet with the platform closest to the wrist being taller than the one closer to the elbow.
    •    Left gauntlet must feature a "comms device" constructed to match references.
    •    Gauntlets will taper to wrist
       ◦    They are flat silver/light grey in color and slightly weathered through.
•    Flight Suit
        •    Must be a cotton or cotton blend, one or two-piece garment colored charcoal grey or black, and must be properly fitted and shaped to the wearer.
    •    Flightsuit has traditional Mandalorian style double sleeves (long sleeves with short sleeves on top). Short sleeves are approximately 80% the length from the shoulder to the elbow of the wearer.
    •    Must not have any visible pockets, pouches or zippers once armor is attached.
    •    There are two options regarding the pant bottoms:
    ◦    Option 1: Legs must be long enough to tuck into the top of the boots.
    ◦    Option 2: Leg length if left untucked must not extend below the ankle of the wearer.
    •    Flight suit must be weathered to match visual references. 
    •    Neck Seal
    ◦    The neck seal will be a straight tube with light padding inside of it. It has a small tuck on the top.
    ◦    It is slightly higher in the back and under the jaw line in the front.
•    Flak Vest
    ◦    The vest is Jango Fett style, black in color.
       ◦    Must have two long shoulder tabs to mount the shoulder armor.
    ◦    Must be made of black leather, leather-like, or similarly sturdy material such as duck cloth or canvas.
       ◦    Vest must be short enough to stop before hitting the girth belt. (Approximately 1-2” long below bottom edge of Ab Armor.)
    ◦    Vest is not tucked into the girth belt and allows some flight suit to show.
    •    Boots
    •    Must be charcoal grey or black canvas with black rubber sole.
    •    Sole must have rugged tread.
    •    Boot must be angle-height.
    ◦    Palladium boots Pampa Hi, in canvas, are an example of an acceptable style. 
    •    Gloves
    •    Must be black in color of cotton, canvas, non-piling material or Leather or faux leather material 
    ◦    May use Nomex pilot gloves.
    •    No visible logos or designs may be present once hand plates are attached..
    •    Belt
    ◦    The front piece of the belt is 1.5-inches wide.
    ◦    The top piece has a ½-inch wide and 2.5-inch high pill-shaped hold cut in it.
    ◦    A ¼-inch wide piece is located on either side of the ‘buckle.’ Then a 1-inch, then a ½-inch, then a 3-inch are located on either side of those.
    ◦    The next pieces will be 2-inches wide and have a 1-inch wide 1-inch high square with rounded edges cut in it.
    ◦    The back of the belt will include similar pieces to cover the entire length. The back piece will be a 3-inch piece with a 2-inch wide, 2-inch high hole in the center as with the sidepieces.
    ◦    Color gunmetal grey or black.
    •    Waist Wrap/Girth Belt
    ◦    Black leather or leather look fabric that matches the Flak Vest approximately 1″ wider than ammo belt at top and bottom
    •    Jetpack
        •    Must be a Death Watch "arena" style (JT-12) jetpack with snub nose center missile and nozzles mounted directly under the tanks on each side.
    •    Must be dark grey and grey/black panels and patterns.
    •    Tank toppers must have a red and white stripe under the cone portion. Red stripe must be under the white stripe.
    ◦    Additional red detailing is present on either side of center tank to match visual references.
    •    Nozzles must be charcoal grey/black.
    •    Jetpack attaches snugly against the back armor in the proper centered position.
    •    Paint scheme weathered to match visual references
    •    Pistols
        •    Must be Animated Deathwatch style Westar 35 Pistols.
    •    Must be painted silver with charcoal grey/black grips, properly weathered to match visual references.
    ◦    The pistols may both be built of equal size to fit in the thigh holsters.
    •    Carbine
    •    Must be Animated Deathwatch style Westar 35 Carbine.
    •    Must be painted silver with charcoal grey/black grips, properly weathered to match visual references.  

 

Mandalorian Super Commando Grunt Vertical Handprint 
•    Helmet
    ◦    An animated Deathwatch style helmet must be used.
    ◦    The dome is painted metallic grey, light grey or silver. The face and back of the helmet are painted black. The mandibles, key slot indentation, and band are painted red. The upper cheeks are painted a light grey and the lower cheeks are painted black.
       ◦    A stylized hand print is placed on the center face of the helmet vertically with the fingertips pointing up and on the front part of the dome. The handprint is painted black with drip marks running down from it.  
    ◦    The helmet should have the narrower design with the longer face and the T should come to points at the ends.
      ◦    The visor should be dark in color to obscure the wearers face.
    ◦    There are no diamonds on the forehead of the helmet.
    ◦    The right earcap must match the left.
    ◦    As with the Clone Wars season 2 Death Watch grunt there is no RF for the Season 4 Death Watch Grunts.
      • Must be weathered according to the visual reference material.
•    Shoulder Plates
       ◦    Must be Animated Death Watch style armor.
       ◦    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
       ◦    Must have 4 points with an inward curve connecting the top and bottom point on each outside edge.
    ◦    They are painted red in color and are weathered through.
       ◦    Armor is connected securely to Flak Vest shoulder tabs.
       ◦    Shoulder armor flares out off the shoulders to present a wider than normal silhouette. 
•    Chest Armor
    ◦    Chest armor must be the animated Deathwatch style and consist of two chest plates, ab plate, diamond, and collar plate.
    ◦    Upper chest plates are hastily painted red in color, showing brush strokes and weathered throughout.
      ◦    The chest diamond is painted red in the same fashion as the upper chest armor. The diamond also has a raised thin rectangular piece in its center.
      ◦    The collar plate is painted red in color in the same fashion as the upper chest plates and weathered throughout
      ◦    The abdominal plate is a dark charcoal grey in color with slight red over spray from upper chest and weathered throughout
    ◦    The chest slots are cut out. The slots should be painted with red paint.
•    Back Plate
    •    Must be Animated Death Watch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must have curved cutout at the bottom.
    •    Interior curved area should match black on armor.
    •    Should curve in towards wearer on all edges to give appearance of thickness, and sit flush against wearers back.
    •    NOTE: Collar and backplate DO NOT overlap.
    ◦    It is ultra flat black in color.
•    Cod Armor
        •    Must be Animated Deathwatch style armor.
    •    Triangular cod piece which must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    ◦    Bottom must curve inward toward the inseam of the wearer.
    •    Must be tucked under the girth belt.
    ◦    It is dark charcoal grey in color and weathered through slightly.
•    Thigh Armor
    ◦    Must be the animated Deathwatch style armor.
      Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    ◦    The plate rides on the outside of the thigh rather than on the front of the thigh.
    ◦    The holsters are built into the thigh plate and appear as part of the armor.
          •    Armor wraps around the outer thigh with no visible straps/attachment.
    •    Must feature a solid box holster on each leg.
    ◦    Rear upper section of holster box is shorter than front to accommodate Westar pistols
    ◦    They are ultra flat black in color.
•    Knee Plate
          •    Must be Animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be painted black and weathered to match references.
    •    Armor attaches to the front of the knees, directly to flight suit with no straps or visible means of attachment
    ◦    The base color is flat silver/light grey. This base color is shown through the weathering.
•    Shin Armor
        •    Must be Animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be painted metallic grey, light gray or silver and weathered to match references.
    •    Must fit closely around the shin.
    •    Must be made of three angled sections: flat front and angled flat sides that curve at back slightly to fit wearers leg. The tops of the side segments must be angled downwards.
    •    Armor attaches directly to flight suit with no straps or visible means of attachment. 
•    Boot Armor
    ◦    Must be animated Deathwatch style armor.
    •    Must appear to be at least 3mm thick with rounded edges in order to give the feeling of thickness and depth. May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Armor consists of Top of the foot cover, Toe Cap and Heel Cover with rectangular raised detail that wraps around back of heel.
    •    Must be painted charcoal grey/black and weathered to match references.
    •    Boot armor connects with no visible means of attachment
    ◦    Near the ankle, the armor should be ultra flat black in color.
•    Spat
    ◦    No spats should be used for the TCW Deathwatch builds.
    ◦    Although due to CGI cheat in the show portrays some movement that could be considered less than hard armor, it has been determined it’s due to animation not actual portrayal.
•    Hand Plates
    ◦    The hand plates are a completely custom design in a ‘tombstone’ shape.
    ◦    They are ultra flat black in color and weathered slightly through.
•    Gauntlets
    ◦    The gauntlets are a completely custom design and do not match the season 2 Death Watch gauntlets.
    ◦    They are a set of clamshell cylinder gauntlets.
    •    Must be Animated Deathwatch style armor.
    •    May be made of a solid material such as fiberglass, resin, styrene, sintra or Vac-formed ABS.
    •    Must be worn with indented "closure" on the inside of the arm.
    •    Must have two raised platforms on the top of the gauntlet with the platform closest to the wrist being taller than the one closer to the elbow.
    •    Left gauntlet must feature a "comms device" constructed to match references.
    •    Gauntlets will taper to wrist
       ◦    They are flat silver/light grey in color and slightly weathered through.
•    Flight Suit
        •    Must be a cotton or cotton blend, one or two-piece garment colored charcoal grey or black, and must be properly fitted and shaped to the wearer.
    •    Flightsuit has traditional Mandalorian style double sleeves (long sleeves with short sleeves on top). Short sleeves are approximately 80% the length from the shoulder to the elbow of the wearer.
    •    Must not have any visible pockets, pouches or zippers once armor is attached.
    •    There are two options regarding the pant bottoms:
    ◦    Option 1: Legs must be long enough to tuck into the top of the boots.
    ◦    Option 2: Leg length if left untucked must not extend below the ankle of the wearer.
    •    Flight suit must be weathered to match visual references. 
    •    Neck Seal
    ◦    The neck seal will be a straight tube with light padding inside of it. It has a small tuck on the top.
    ◦    It is slightly higher in the back and under the jaw line in the front.
•    Flak Vest
    ◦    The vest is Jango Fett style, black in color.
       ◦    Must have two long shoulder tabs to mount the shoulder armor.
    ◦    Must be made of black leather, leather-like, or similarly sturdy material such as duck cloth or canvas.
       ◦    Vest must be short enough to stop before hitting the girth belt. (Approximately 1-2” long below bottom edge of Ab Armor.)
    ◦    Vest is not tucked into the girth belt and allows some flight suit to show.
    •    Boots
    •    Must be charcoal grey or black canvas with black rubber sole.
    •    Sole must have rugged tread.
    •    Boot must be angle-height.
    ◦    Palladium boots Pampa Hi, in canvas, are an example of an acceptable style. 
    •    Gloves
    •    Must be black in color of cotton, canvas, non-piling material or Leather or faux leather material 
    ◦    May use Nomex pilot gloves.
    •    No visible logos or designs may be present once hand plates are attached..
    •    Belt
    ◦    The front piece of the belt is 1.5-inches wide.
    ◦    The top piece has a ½-inch wide and 2.5-inch high pill-shaped hold cut in it.
    ◦    A ¼-inch wide piece is located on either side of the ‘buckle.’ Then a 1-inch, then a ½-inch, then a 3-inch are located on either side of those.
    ◦    The next pieces will be 2-inches wide and have a 1-inch wide 1-inch high square with rounded edges cut in it.
    ◦    The back of the belt will include similar pieces to cover the entire length. The back piece will be a 3-inch piece with a 2-inch wide, 2-inch high hole in the center as with the sidepieces.
    ◦    Color gunmetal grey or black.
    •    Waist Wrap/Girth Belt
    ◦    Black leather or leather look fabric that matches the Flak Vest approximately 1″ wider than ammo belt at top and bottom
    •    Jetpack
        •    Must be a Death Watch "arena" style (JT-12) jetpack with snub nose center missile and nozzles mounted directly under the tanks on each side.
    •    Must be dark grey and grey/black panels and patterns.
    •    Tank toppers must have a red and white stripe under the cone portion. Red stripe must be under the white stripe.
    ◦    Additional red detailing is present on either side of center tank to match visual references.
    •    Nozzles must be charcoal grey/black.
    •    Jetpack attaches snugly against the back armor in the proper centered position.
    •    Paint scheme weathered to match visual references
    •    Pistols
        •    Must be Animated Deathwatch style Westar 35 Pistols.
    •    Must be painted silver with charcoal grey/black grips, properly weathered to match visual references.
    ◦    The pistols may both be built of equal size to fit in the thigh holsters.
    •    Carbine
    •    Must be Animated Deathwatch style Westar 35 Carbine.
    •    Must be painted silver with charcoal grey/black grips, properly weathered to match visual references.  

 

[DarthValkyria]

The Bounty Hunters Guild is more than just Bounty Hunters, but we (us and the BHG DL) have argued for a new designation, but currently, to no avail.